An ATIS trailer wash bay procedure should use the cleaning limits for the installed equipment, identify approved products and methods, and provide a clear route for reporting damage or abnormal conditions. Do not assume that an inflation system can tolerate every pressure washer, detergent or spray direction simply because it is installed on a commercial vehicle.
This guide helps fleet maintenance teams and wash contractors agree the work boundary. It does not supply a universal spray pressure, nozzle distance, chemical concentration or water-resistance rating. Those details must come from the actual equipment instructions and the responsible technical review before staff are asked to use them.

Start by identifying what is being cleaned
List the trailer groups and relevant installed equipment rather than writing one instruction for an undefined fleet. Depending on the design, visible components and access needs may differ. Have the technical owner identify the areas requiring particular attention under the current instructions, without inventing restrictions from a photograph of a different system.
Make the resulting information usable at the wash location. A contractor needs the asset or configuration identifier, the applicable method and a contact path for uncertainty. A large folder that cannot be found during the job is not an effective working instruction, even if procurement received it at installation.
ATIS trailer wash bay: the approval worksheet
| Item | What the fleet should establish | Supporting record |
|---|---|---|
| Equipment scope | The installed models and relevant exposed areas | Configuration and identification sheet |
| Cleaning method | Allowed method and equipment-specific limits | Current technical instructions |
| Chemical use | Suitability for the equipment and worker protection | Product information and safety data |
| Inspection | What is observed before and after the job | Position-specific checklist |
| Exception | Who responds to missing instructions or reported damage | Maintenance escalation record |
This worksheet defines questions to resolve, not a cleaning approval by itself. If a limit is unknown, mark it unknown and obtain a competent answer. Do not replace missing equipment guidance with the highest or lowest setting available on a pressure washer and assume that the choice is safe.
Separate chemical safety from component compatibility
A product’s safety data sheet informs worker protection and handling; it does not automatically approve the product for every hose, seal, coating or electrical component. Obtain the necessary equipment compatibility guidance separately. Keep the cleaning product identity and working method consistent with the approved procedure.
The OSHA/NIOSH cleaning-chemical information sheet discusses selecting chemicals, consulting safety data and protecting workers. Its recommendations do not certify a cleaner for an ATIS installation. Use that distinction when a contractor proposes a substitute product.
Make worker instructions understandable
Staff should know which procedure applies, where they may work and how to stop the task when instructions are missing. For covered U.S. workplaces, OSHA’s Hazard Communication standard addresses information and training about hazardous chemicals. Other jurisdictions have their own applicable requirements.
Do not treat a signed attendance sheet as proof that a temporary employee understood a particular wash method. Have the responsible supervisor verify understanding using the actual task and language needed at the site. Keep chemical handling and equipment restrictions clear without turning the inspection sheet into an improvised repair manual.
Record relevant condition before washing
Use safe external access to note visible concerns already present before the job. Identify the asset and area so later staff can distinguish an earlier report from a new observation. Photographs can help document visible condition, but they do not establish the state of hidden components or prove that a system was functioning correctly.
If staff notice displaced equipment, visible damage or an abnormal indication, report it through maintenance. Do not ask the wash crew to determine the cause or restore a component outside its authorised role. Washing should not become an undocumented technical intervention because a worker wants to return the trailer quickly.
Respect the tire-service boundary
Cleaning and tire servicing are different tasks. The USTMA commercial tire-care manual provides the tire inspection and service context. A wash record should not claim that tire pressure, internal condition or serviceability was verified unless the required assessment actually occurred.
Where cleaning reveals a concern needing access, disassembly or measurement, refer it to competent personnel under the appropriate procedure. Do not remove wheel equipment, loosen a fitting or adjust pressure simply to improve cleaning access. The presence of water or detergent does not reduce the hazards associated with stored pressure or wheel service.
Agree what the post-wash check actually establishes
Define observable checks using the applicable equipment instructions. Relevant entries may include visible condition of identified areas, retained covers or guards, and any indication staff are authorised to observe. Record what was seen, when and by whom. Avoid a blanket “ATIS tested” statement when the crew performed only an external visual check.
If the instructions require a functional check, identify the authorised person and required record. Do not invent a universal test or acceptance threshold. An incomplete required check needs a named action and a clear operating disposition under the fleet’s release process, not an unexplained tick in the wash log.
Handle a concern reported after washing
Keep the sequence of events without assuming causation. Record the pre-wash condition, cleaning information available, post-wash observation and any subsequent technical findings. A fault reported after a wash may justify review, but timing alone does not establish that cleaning caused it.
Preserve the original work order and ask support what additional evidence is useful. Do not repeat a potentially unsuitable cleaning method to reproduce a symptom. The wheel-end serviceability guide can help frame questions about visible equipment where applicable, but the installed-system documentation governs the actual review.
Include outside wash contractors
Give contracted providers the relevant current instructions before they accept the work. Define what they must report, how they identify the trailer and who receives exceptions. A general contract promising “professional cleaning” does not explain the limits for a specific installation or allocate technical release responsibility.
When the contractor changes chemicals, cleaning equipment or process, determine whether the approved method needs review. Keep the change visible to the fleet technical owner. Do not assume the first assessment remains valid after important working conditions have changed, or that every depot uses the same products.
Trial the process before broad rollout
Use a representative authorised configuration and a defined cleaning method to confirm that staff can follow the instructions and complete the required observations. Record the product and procedure references, questions raised and actions needed. This is a proposed process review, not a claim of a completed customer trial.
Evaluate practical issues such as document access, exception reporting and handback to maintenance. One wash does not prove lifetime resistance to chemicals, corrosion or water ingress. Any durability or protection claim should be supported by evidence with a defined scope, not inferred from the absence of a visible concern during a short demonstration.
Frequently asked questions
Can a pressure washer be used around every ATIS installation?
Do not assume universal permission. Obtain the applicable cleaning instructions and have the responsible reviewer resolve the actual equipment and method.
Does a safety data sheet prove that a cleaner is compatible?
No. It addresses chemical hazards and handling information. Component compatibility and the allowed cleaning method require separate relevant evidence.
Does a successful wash prove that the system is waterproof?
No. A single event does not establish a protection rating or durability claim. Use the evidence and limitations for the exact model and configuration.
Discuss your fleet’s cleaning environment
Contact IntelliSafeAir with your vehicle group, operating market, cleaning method and contractor arrangement. Identify available instructions and unresolved questions before choosing a pilot. The fleet evaluation guide supports a vehicle-fitment or distributor service-support discussion.
References
Reviewed October 18, 2026. The workflow is an editorial framework. Sources support chemical-worker protection and tire-care context; none supplies a model-specific ATIS wash approval.